Needle Punch Tutorial & Free Project

Needle Punch Tutorial & Free Project

Needle punch is a simple way you can easily and quickly create beautiful stitched patterns and designs. We’ll show you how to set up your needle punch tool, our recommended thread and materials, and walk you through simple tips on how you can use this technique to create different textures and stitches. We’ve even included a few FREE printable patterns below to help get you started on your next needle punch project!

Materials:

  • Download the free patterns here
  • Recommended thread: Eleganza™ #8 perle cotton thread: https://wonderfil.eu/collections/eleganza-8-perle-cotton
  • Needle punch tool (we used one by Clover)
  • Embroidery hoop (to fit the free patterns above, we used a 5.5” hoop)
  • 100% cotton monk’s cloth with an even weave
  • (optional) A light table to trace your pattern onto the fabric, we used one by Daylight
  • Clear glue

A picture containing person, indoor, holding, table

Description automatically generated

Before you can begin needle punching, you’ll need to prepare your fabric. Download one of the patterns from the link above or select one of your own. You can trace this pattern onto your monk’s fabric using a light table or by holding it up against a window. Some patterns can also be transferred using an iron or with carbon paper and will come with instructions on how to do so.

A picture containing person, indoor, table, food

Description automatically generated

We recommend using a 100% cotton monk’s cloth with an even weave as this will be the easiest to keep your stitches looking consistent and straight.

A close up of a piece of paper

Description automatically generated

Once your pattern is traced, hoop the fabric tightly in an embroidery hoop. For the free patterns available above, we used a size 5.5” hoop. You can then proceed to load your needle punch tool with thread. Our recommendation is a #8 size perle cotton as this will offer enough friction in the fabric to hold, while still showing boldly. We used #8 Eleganza perle cotton as it has a very tight twist which prevents untwisting, and a low lint finish that allows it to pull easily through the fabric.

A picture containing pink, sitting, display, food

Description automatically generated

Your needle punch should come with a needle threader. Slide it through the tool from the base of the needle so that the threader is facing the top end of the punch. You can then slide the thread through the threader loop and pull it back through the punch, drawing the thread with it through to the base of the needle.

A picture containing baseball, holding, player, man

Description automatically generatedInserting the needle threader

A hand holding a piece of paper

Description automatically generatedSliding the thread through the needle threader’s loop

A close up of a sign

Description automatically generatedDrawing the needle threader back out, pulling the thread with it. Your needle punch is now threaded!

Leave a tail of a few inches of thread and slowly begin punching through the fabric, filling in the design. You’ll notice two sides to the fabric, one that sticks out with loops, and the backside which is shorter. You can choose to make either side your “right” side.

A hand holding a piece of paper

Description automatically generatedFront side

A picture containing person, cake, piece, holding

Description automatically generatedBack side

For reference, the side you do the punching from will be the “back side” of the fabric, while the opposite side will be the “front side”. When you’re finished filling in a section, trim away the thread and secure the back side with clear glue.

A picture containing indoor, table, sitting, food

Description automatically generated

To create an optional fun texture, you can take a pair of scissors and cut the loops on the front side of the fabric, releasing them. You’ll end up with a soft and fuzzy texture that can be trimmed down around the edges of the design to keep the edges clean and crisp.

A hand holding a knife

Description automatically generatedCutting the loops

A picture containing cake, indoor, plate, piece

Description automatically generatedThe resulting texture after cutting the loops

To change the texture and add a bit of contrast in the design, we’ll be flipping the hoop over and punching from the “front side” instead of the “back side”. Since these stitches will now be more visible, an option while you’re filling in the design is to move back and forth in a zig zag pattern. This creates an even satin stitch that mimics the shape of the leaf.

A picture containing person, holding, hand, small

Description automatically generated

Once again, when you’re finished filling in a section, trim away the thread and apply clear glue to secure the stitches at the start and end of the thread.

A hand holding a piece of paper

Description automatically generated

Play with the side you punch from to create a variety of textures for your project! Continue these steps until your design is complete. Below is the front side of our hoop.

A picture containing person, holding, indoor, hand

Description automatically generated

To finish your hoop, trim the fabric to the edge of the hoop. We’ll be leaving our design in the hoop to frame and hang it.

A person holding food

Description automatically generated

Experiment with the textures you can create using this fun and simple tool! This is a versatile way to efficiently fill in designs in by hand and get creative.

A picture containing indoor, cake, clothing, table

Description automatically generated

A picture containing cake, indoor, table, piece

Description automatically generated

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.